 |
23. IN2-W Turf-Tec
Infiltrometer $ 495.00 |
Instrument is used to determine
water infiltration rate easily in a matter of minutes. A must to keep diseases to a
minimum. Turfgrass areas can be monitored periodically to determine whether infiltration
is staying constant or decreasing. The Turf-Tec Infiltrometer is useful in
fields like geology, geotechnical, engineering, hydrology, forestry,
environmental testing, hydrogeological, runoff studies, wetland mitigation,
permeability testing, sanitation contractors, project planning, stormwater
best management practices and EPA requirements.
  Click here to see
literature on this item.
Click here to order this product |
 |
25. IN7-W -
Turf-Tec Heavy Duty Infiltration Rings 6 and 12 inch diameter by 4 inches
tall $ 275.00 |
The Turf-Tec Infiltration Rings allow for field infiltration rates to be
measured in hard or rocky soils. This tool is ideal for turfgrass students. It
has a 6 inch inner ring and a 12 inch diameter outer ring with a 4 inch height.
A welded gripped handle is attached to the galvanized rings to allow easy
insertion into the soil and to insure proper centering of the rings. These
Infiltration rings are made of heavy duty 16 Gauge (.065 inch) galvanized steel.
Click here to see literature on this item.
Click here to order this product |
 |
IN8-W -
Turf-Tec Heavy Duty Tall Infiltration Rings
6 and 12 inch diameter by 7 inches tall $ 375.00 |
Turf-Tec Heavy Duty Tall Infiltration Rings have a 6 inch inner ring and
a 12 inch outer ring with a 7 inch height. A gripped rubber handle is welded
across the rings to keep them concentric and allow easy insertion into, and
removal from the soil. These rings are ideal for hard soil types. These
Infiltration rings are made of heavy duty 16 Gauge (.065 inch) galvanized steel.
Click here to see literature on this item.
Click here to order this product |
 |
26A. IN8P-W -
Turf-Tec Heavy Duty Tall Infiltration Rings
6 and 12 inch diameter by 7 inches tall with Ports $ 425.00 |
Turf-Tec Heavy Duty Tall Infiltration Rings are identical to above units but
have ports added to allow rings to be attached to IN12-W Mariotte Tubes (Item #
30 not included). The rings have a 6 inch inner ring and
a 12 inch outer ring with a 7 inch height. The ports are located three
inches above the bottom of the ring to allow up to three inch insertion into the
soil. A gripped rubber handle is welded
across the rings to keep them concentric and allow easy insertion into, and
removal from the soil. These rings are ideal for hard soil types. These
Infiltration rings are made of heavy duty 16 Gauge (.065 inch) galvanized steel.
Click here to see literature on this item
Click here to order this product |
 |
27. IN6-W -
Turf-Tec Driving Plates for all Turf-Tec 6 and 12 inch Infiltration Rings $
99.00* Note- Price is for plate only! |
New!
The new driving plate for the Turf-Tec 6 and 12 inch Infiltration Rings
allow the infiltration rings to be hammered into the ground for ease of
insertion. The specially designed plate fits directly overtop the center handle
assembly on the IN5-W, IN7-W and IN8-W model Infiltration Rings.
*Note- Price is for driving plate only, not rings!
Click here to see literature on this item
Click here to order this product |
 |
28. IN10-W Turf-Tec
Infiltration Rings 12 and 24 Inch $ 600.00
|
The Turf-Tec Infiltration Rings have diameters of 12 and 24 Inches
and match ASTM standard D3385-09 for soils with a hydraulic conductivity between 1X10-2 cm/s
or less than about 1 X 10-6 cm/s or sand type soils with high infiltration rates.
These Infiltration rings are made of heavy duty 16 Gauge (.065 inch)
galvanized steel. They are constructed of durable steel and braced with welded steel supports to insure the rings stay evenly centered as they penetrate the soil.
They are galvanized to prevent rust and insure long life. We suggest
also seeing item # 30 - IN12-W Turf-Tec Mariotte Tubes for use with IN10-W (Sold
Separately)
Click here to see literature on this item
Click here to order this product |
 |
28A. IN14-W Turf-Tec Heavy Duty Infiltration Rings 12 and 24 Inch $ 900.00
|
The Turf-Tec Heavy Duty Infiltration Rings have diameters of 12 and 24 Inches
and match ASTM standard D3385-09 for soils with a hydraulic conductivity between 1X10-2 cm/s
or less than about 1 X 10-6 cm/s or sand type soils with high infiltration rates.
These Infiltration rings are made of heavy duty 14 Gauge (.10 inch)
galvanized steel. They are constructed of durable steel and braced with welded steel supports to insure the rings stay evenly centered as they penetrate the soil.
They also have a 1/4 inch thick steel band welded along the top edge to allow
driving into hard soils. They are galvanized to prevent rust and insure long life. We suggest
also seeing item # 30 - IN12-W Turf-Tec Mariotte Tubes for use with IN10-W (Sold
Separately)
Click here to see literature on this item
Click here to order this product |
 |
29. IN11-W Turf-Tec
Driving Plates for 12 and 24 Inch Infiltration Rings $ 230.00*
Note- Price is for plate only!
|
The new driving plate for the Turf-Tec 12 and 24 inch Infiltration Rings
(IN10-W and IN14-W) allow the infiltration rings to be hammered or jacked into the ground
for ease of insertion. The specially designed plate fits directly overtop the
center handle assembly on the IN10-W and IN14-W model Infiltration Rings.
*Note- Price is for driving plate only, not rings!
Click here to see literature on this item
Click here to order this product |
 |
30. IN12-W Turf-Tec Mariotte Tubes for use
with IN10-W
or IN14-W or IN8P-W (Above) $
650.00 |
Turf-Tec Mariotte Tubes match the ASTM for standard testing of soils with a
hydraulic conductivity between 1X10-2 cm/s or sand type soils with high
infiltration rates. These tubes are a companion tool for using with the Turf-Tec
12 and 24 inch Infiltration Rings (IN10-W) or the Turf-Tec Heavy Duty Tall
Infiltration Rings 6 and 12 inch with Ports (IN8P-W) . The Turf-Tec Mariotte Tubes match
the ASTM Standard D 3385-09 if combined with the IN10-W. They are
constructed of heavy wall PVC tubing and have solid brass and stainless steel
fittings.
* IN10-W, IN14-W and IN8P-W Infiltration Rings sold separately
Click here to see literature on this item
Click here to order this product |
 |
30. IN12A-W Turf-Tec
10,000 ml ONLY - Mariotte Tube for use with IN16-W (Below) $ 400.00 |
This single 10,000 ml
Turf-Tec Mariotte Tubes match the ASTM for standard testing of soils with a
hydraulic conductivity between 1X10-2 cm/s or sand type soils with high
infiltration rates. It is designed to be used with the new IN16-W Turf-Tec Heavy
Duty 12 Inch Diameter is a single ring Infiltration Ring has a diameters of 12
Inches (30 CM) and an overall height of 20 inches (50 CM).
Click here to see literature on this item
Click here to order this product |
 |
30A.
IN16-W - Turf-Tec Heavy Duty 12 Inch Diameter Infiltration Ring $ 450.00 |
The new Turf-Tec Heavy Duty 12 Inch Diameter is a single ring Infiltration Ring
has a diameters of 12 Inches (30 CM) and an overall height of 20 inches (50 CM).
This single ring Infiltrometer is constructed of very heavy duty and durable
galvanized steel and topped with a 1/4" thick steel reinforced top edge for
driving into the soil.
Click here to see literature on this item
Click here to order this product |
 |
30B.
IN17-W - Turf-Tec Heavy Duty 12 Inch Diameter Driving Plate
for use with IN16-W Infiltration ring $ 200.00 |
The new IN17-W - Turf-Tec Heavy Duty 12 Inch Diameter Driving Plate is specially
designed to be used with the Turf-Tec Heavy Duty 12 Inch Diameter Infiltration
Ring (IN16-W) Click here to see literature on this item
Click here to order this product |
 |
31. IN13-W Large Volume Mariotte Tubes for use with 12
and 24 Inch Diameters Infiltration Rings $ 1800.00* |
The new Turf-Tec Large Volume Mariotte Tubes match the ASTM for standard testing
of soils with a hydraulic conductivity around 1X10-2 cm/s or sand type soils
with very high infiltration rates. The new large volume tubes can also hold a large
volume of water for extended testing periods. They are constructed of
heavy wall PVC tubing and have solid brass and stainless steel fittings.
Note these tubes are for very sand soils and hold 100,000 ml (100 liter or about
26 gallons) each.
* IN10-W or IN14-W Rings sold separately
Click here to see literature on this item
Click here to order this product |

 |
32. IN15-W Turf-Tec SDRI 5 foot and 12 foot Infiltration
Rings $ 6000.00 |
The new Turf-Tec Infiltration Rings have diameters of 5 foot and
12 foot diameter rings that match ASTM Standard D 5093-02 which replaced old ASTM D
5093-90. The Turf-Tec Infiltration Rings are double ring for standard
testing of soils with a hydraulic conductivity between 1X10-7 m/s to 1X10-10 m/s
or tight soils with very low infiltration rates.
These units are now kept in stock and ready for immediate shipping!
Click here to see literature on this item.
Click here to order this product |
BACK TO TOP
Click here to go to a alphabetical listing of all products with photos
Click here to go to a alphabetical listing of all products without photos
Click here to go to the page with a group photo of all products

Soil Moisture Meters Section |
 |
33. MS1-W Turf-Tec Moisture
Sensor $ 400.00 |
The Turf-Tec Moisture Sensor is
calibrated in percentages - read outs are immediate. Check moisture at any level from
1 inch to 4 inches deep. Quick adjustable base allows easy depth adjustment.
Unit will also identify dry spots before they become visually apparent and water movement
problems. Readings are in percentages.  Click here to see
literature on this item
Click here to order this product |
 |
Replacement Part for MS1-W
34. TTMP75-W - Moisture
Sensor Replacement Probe and wire (For MS1-W) $ 90.00
This is a replacement probe and wiring assembly for the Turf-Tec Moisture
Sensor.
Click here to see
literature on this item
Click here to order this product |
 |
Replacement Part for MS1-W
35. TTMP26-W - Moisture Sensor Replacement 4 inch Steel
Spikes (Set 2) (For MS1-W) $ 25.00
These replacement spikes are for the Turf-Tec Moisture Sensor foot assembly.
Click here to see
literature on this item
Click here to order this product |

 |
33A.
MSFS1-W Field Scout Digital Moisture Sensor with soft case
and one set
spikes (TDR 300) $ 1,100.00 |
The Field Scout TDR 300 Digital
Moisture Sensor allows you to monitor and record soil moisture quickly and
accurately with TDR technology (time-domain measurement technology). The
Field Scout Digital Moisture Sensor offers turfgrass managers a portable
unit to accurately measure soil moisture across the full range of soil
moisture conditions. It includes a internal data logger and runs on 4
AAA batteries. Unit includes one set spikes
(You can specify probe length), software and 7 pin serial cable and soft
carrying case.
Click here to order this product
Click here to see literature on this item
MSFS1-W-1.5 - Field Scout Digital Moisture Sensor with 1.5 inch (3.8cm) probes and Case $1100.00
MSFS1-W-3.0 - Field Scout Digital Moisture Sensor with 3.0 inch 7.5cm) probes and Soft Case $1100.00
MSFS1-W-4.8 - Field Scout Digital Moisture Sensor with 4.8 inch (12 cm) probes and Soft Case $1100.00
MSFS1-W-8.0 - Field Scout Digital Moisture Sensor with 8.0 inch (20 cm) probes and Soft Case $1100.00
MSFSP01 Replacement Spikes 1.5 inch (3.8cm) - (set of 2) $57.00
MSFSP03 Replacement Spikes 3.0 inch (7.5cm) - (set of 2) $57.00
MSFSP04 Replacement Spikes 4.8 inch (12 cm) - (set of 2) $57.00
MSFSP05 Replacement Spikes 8.0 inch (20 cm) - (set of 2) $57.00

MSFS1-USB-Cable - 7 pin Serial to USB Cable $32.00
MSFS1-Case - Replacement Digital Moisture Sensor Soft Carrying Case $128.00
NEW - MSFSBT-W - Bluetooth Attachment for MSFS1 Digital Moisture Sensor - $248.00
NEW - MSFSSC-W SpecConnect FieldScout Pro Subscription (1-yr)Up to 3 devices $
199.00
NEW - MSFSSC-ADD-W -
SpecConnect Additional FieldScout Device (1-yr)
Click here to order this product
|

 |
33C.
MSFS-TDR100-W - Field Scout Handheld Digital Moisture Sensor (TDR 100) $730.00* |
The Field Scout Handheld Digital Moisture Sensor allows you to monitor and record soil moisture quickly and accurately
with TDR technology (time-domain measurement technology). Field Scout Digital
Moisture Sensor offers turfgrass managers a tool to eliminate the guesswork.
Based on proven time-domain measurement technology, this portable unit accurately measure soil moisture
across the full range of soil moisture conditions. It comes with readout
display, Probe block and a 5 ft (1.5 m) cable as well as hard carrying case.
This unit does not have data logging capability.
* Note price does not include
probes - You will need one set of probes to operate unit*
Click here to see
literature on this item
MSFS-TDR100-W - Field Scout Handheld Digital Moisture Sensor (TDR 100) $ 730.00 (Without spikes)
Click here to order this product
MSFSP01 Replacement Spikes 1.5 inch (3.8cm) - (set of 2) $57.00
MSFSP03 Replacement Spikes 3.0 inch (7.5cm) - (set of 2) $57.00
MSFSP04 Replacement Spikes 4.8 inch (12 cm) - (set of 2) $57.00
Click here to order the spikes
|
  |
33D.
MS6-W - Turf-Tec Digital Moisture Sensor $600.00 |
The Turf-Tec Digital Moisture Sensor has an adjustable foot which allows
moisture readings at the one, two three and four inch depth without
changing probes. Simply slide the adjustable foot to the desired depth,
insert the Turf-Tec Digital Moisture Sensor into the soil and after five
seconds, read the digital display to see the amount of moisture that is held within the air space in the soil.
This state of the art unit is designed to work in all soil types and
salinity ranges. The probes are also easily replaceable. The Turf-Tec
Digital Moisture Sensor uses a newly designed electrical conductivity
sensing circuit that gives quick and reliable readings of soil moisture.
With years of science behind the sensing results, there is no easier way to
test for soil moisture.
Click here to see literature on this item
Click here to order this product |
 |
Replacement Part for MS6-W |
The Turf-Tec Digital Moisture Sensor has a set of replacement spikes.
These ate easily unscrewed and new spike can then be re-inserted into the
foot. Note - Spikes are sold in a set of two and it is suggested that
they both be replaced at the same time. Spikes are also color coded to
insure proper assembly.
MS6P001 Replacement Spikes - (set of 2) (For MS6-W) $90.00
Click here to order this product |
  |
33E. POGO II - Soil Moisture Sensor (VWC) with
WiFi (with EC and temperature) $ 2300.00 -
SALE
$1800.00*
(Non integrated GPS Model)* |
The new Stevens Pogo II VWC Moisture Sensor allows you to gain the most
insight into your turf and soil conditions with minimal effort. You simply
insert the Pogo VWC Moisture Sensor into the soil and press read on your
cell phone or tablet and the VWC (Volumetric Water Content) Moisture percentage, Soil EC and Soil
Temperature in F/C are displayed instantly. Readings can be read and
discarded or saved into a downloadable database. The Pogo II - Soil Moisture
Sensor comes with WiFi, re-chargeable battery, charger and hard case.
Click here to see literature on this item
POGO2-W - POGO VWC Soil Moisture Sensor Bluetooth (with
EC and Temp) SALE !!!!
$1800.00 (Non integrated GPS Model)*
Click here to order this product
POGO2-GPS-W - POGO VWC Soil Moisture Sensor Bluetooth with integrated GPS (with
EC and Temp) $2300.00
Click here to order this product
|
   |
33F. POGO-MINI-W - POGO Mini Soil Moisture Sensor (VWC) with Bluetooth (EC and
temperature) $ 940.00 |
The Pogo Mini Moisture Sensor is a cost-effective alternative to moisture
sensing for those who just want a spot reading of Volumetric Water Content
(VWC) along with EC (salinity) and canopy temperature without the additional
mapping features of the full version POGO. It still contains the high
quality POGO sensor that instantly measures moisture on the spot and
displays it on a smart phone or tablet that is within the Bluetooth range.
Click here to see literature on this item
Click here to order this product |
  |
35C. IRR___(Depth)-W - Turf-Tec Model R Irrometer -
Tensionometer |
The Model R is the standard one-piece Irrometer for general use with
irrigated row, tree, and field crops, but can also be used in greenhouse and
nursery applications or for monitoring Vadoze Zones. Simply insert it into
the soil and after about 24 hours, the ceramic block will reach equilibrium
with the soil and give the moisture level. Leave it installed in the soil
and you can periodically check to see when your crops or trees need
additional irrigation.
Click here to see literature on this item
IRR6-W - 6 inch Model
Irrometer $ 79.00
IRR12-W - 12 inch Model
Irrometer $ 82.00
IRR24-W - 24 inch Model
Irrometer $ 88.00
IRR36-W - 36 inch Model
Irrometer $ 95.00
Click here to order this product
IRRKIT-W - Irrometer Service Kit - Includes Vacuum Hand Pump, 1 oz. Irromerter Fluid, 25 Monthly Chart Forms $63.00
Click here to order this product
IRRTOOL-W - Irrometer 7/8” Insertion Tool, 30 inch long
$139.00 |
 |
36. ETG1-W - Evapotranspiration
(ET) Gauge $ 400.00 |
This evapotranspiration gauge easily shows the
amount of water needed for irrigation by reading the sight glass. All you add is distilled
water. Daily readings can be taken to save water. Click here to
see literature on this item
Click here to order this product
|
 |
36A. WIND1-M - SKY-MASTER WIND & WEATHER METER $ 200.00 |
This easy to use, pocket-size weather station features
complete wind speed functions, humidity, dew point, altitude, barometric
pressure with 16 hour graph, temperature, wind-chill, heat index and
includes a severe weather audio alarm. The unit is also water resistant
and closes up into the jack knife style protective case.
Click here to see literature on this item
Click here to order this product
|

|
36B. Light-DLI-W - Light Meter - Day Light Indicator $ 56.00 |
Turf-Tec International is now offering the Daylight Indicator - Light Meter. This pocket sized light meter is a simple and easy step in measuring the light intensity levels outdoors, on golf greens, stadiums or inside a greenhouse. Simply place it on the area to be tested and 24 hours later, it will display your Daily Light Integral (DLI). After 24 hours, simply look at the meters face and see how many LED lights are illuminated. The more lights, the healthier the turf, crops or plants will be. Battery included.
Click here to see literature on this item
Click here to order this product
|
 |
37. PUGS2-W Turf-Tec
Precipitation / Uniformity Gauges $ 225.00 |
This set of 20 calibrated gauges
will indicate how much water is being applied by each sprinkler head and how uniform is
the coverage. Simply set out the gauges between the sprinkler heads and run your
irrigation cycle for 15 minutes. Find out if sprinkler systems are working properly.
Click here to see literature on this item
Click here to order this product
|
BACK
TO TOP |
 |
38. ROM3-W -
Wireless Rain
Gauge with Outdoor Thermometer and 9-day Memory $ 80.00 |
Turf-Tec Wireless Rain Gauge is
wireless and includes a 9-day memory function plus an indoor/outdoor
temperature. This electronic rain gauge has a self-tipping bucket that automatically empties after each
4/100th inch (1 mm) of rain. The reading is recorded on a LCD counter which
mounted indoors. It is also an Electronic Rain Gauge, Electronic
Outdoor Thermometer and an Electronic Indoor Thermometer with memory highest
and lowest temperatures.
Click here to
see literature on this item
Click here to order this product
|
 |
41. TCLEAN1-M Trim-Clean Sprinkler
Head Trimmer
$ 175.00 |
This new tool is simply inserted over sprinkler heads and heavy gauge serrated stainless steel blade is rotated to cut grass and stolons around head.
Unit has interchangeable heads that allows 5", 6", 7" or 8" inch (12.5, 15.0, 17.5 & 20 cm)
blades to be attached the 32 inch heavy duty handle. Note inch size is outside diameter so units trim about 1/8" smaller.
Trim Clean is sold with one handle and one cutter blade. Please specify cutter blade size when
ordering.
Click here to see literature on this item.
TCLEAN1-5-M - Trim Clean with 5" Head (12.5 cm) $175.00
TCLEAN1-6-M - Trim Clean with 6" Head (15.0 cm) $175.00
TCLEAN1-7-M - Trim Clean with 7" Head (17.5 cm) $175.00
TCLEAN1-8-M - Trim Clean with 8" Head (20 cm) $175.00
Click here to order this product
|
 |
Replacement Part for TCLEAN1-M
42. TCLEAN-Head - Replacement head for Trim Clean
Sprinkler head trimmer $ 80.00
This head replaces the worn head on the Trim Clean Sprinkler Head Trimmer.
TCLEANB-5-M - 5" Replacement head
TCLEANB-6-M - 6" Replacement head
TCLEANB-7-M - 7" Replacement head
TCLEANB-8-M - 8" Replacement head
Click here to order this product
|

|
43. DTB size-M Donut Trimmer
Edging Blades (Set 6) $ 198.00 |
Blades attach on your string
trimmer and allow you to trim around sprinkler heads with one pass. They are made to fit
right over the sprinkler heads for trimming. Blades come in 6", 7" and
8" diameters. Six blades per package. Mix and match any size you need.
Click here to see literature on this item
DTB-5-M - Set of 6 - 5 inch Donut Trimmer Edging Blades
DTB-6-M - Set of 6 - 6 inch Donut Trimmer Edging Blades
DTB-7-M - Set of 6 - 7 inch Donut Trimmer Edging Blades
DTB-8-M - Set of 6 - 8 inch Donut Trimmer Edging Blades
Click here to order this product
|

|
AQ__-M (Size)
Aqua-Quicks w/90 Adapter (Set of 2) $ 199.00 |
**Aqua-Quicks are sold 2 per set
w/riser and 2 hose adapters (3/4" or 1").**
This device can turn most Rainbird or Toro valve-in-head sprinkler into a 1"
water source. Made of solid aluminum, simply remove the sprinkler head drive
and put the Aqua-Quick in its place. PLEASE SPECIFY TYPE, SIZE OF AQUA-QUICK
AND
SIZE OF HOSE ADAPTORS. Click here to see literature
on this item.
AQ650-1-M - Toro 630,660,730,760,830,860 & DT34 or DT35 1" inlet sprinkler body - For 1" Hose
AQ650-3-4-M - Toro 630,660,730,760,830,860 & DT34 or DT35 1" inlet sprinkler body - For 3/4" Hose

AQRB700-1-M - Fits all Rainbird 700 series for 1" Hose
AQRB700-3-4-M - Fits all Rainbird 700 series for 3/4" Hose
Click here to order this product
|
BACK TO TOP
Click here to go to a alphabetical listing of all products with photos
Click here to go to a alphabetical listing of all products without photos.
Click here to go to the page with a group photo |